PRODUCT

PRODUCT

HOME > PRODUCT > PRODUCT
제품번호 : 9602, 9602-220
제품명 : 108C Auto Carbon Coater
메이커 : TedPella Inc.
첨부파일 :

108C Auto Carbon Coater

for scanning electron microscopy sample preparation and x-ray micro-analysis



The 108C Auto Carbon Coater with 120mm Ø Chamber

The 108C Auto Carbon Coater is one of the most advanced sample coaters available for coating non-conductive specimens prior to SEM X-ray analysis. The unique feedback-controlled rod evaporation system gives multiple evaporations of around 20nm thickness without any need for rod shaping or adjustment. The high purity stepped carbon rods used in the 108C Auto deliver a superior coating quality usable at high magnifications. The 108C is a compact system, simple to operate and has very rapid pumping cycle time. The option of the MTM-10 High Resolution Thickness Monitor allows conducting carbon films to be tailored to the exact requirements of the sample.

The 108C Auto Carbon Coater uses a novel evaporation supply. Current and voltage are monitored by sensor wires in the head, and the evaporation source is controlled as part of a feedback loop. The supply gives the conventional rod feed source excellent stability and reproducibility. Power consumption is low, and the source shows exceptional re-starting characteristics. The evaporation source can be operated in "pulse" or "continuous" modes.

How do the 108C Auto and the 108C Auto/SE compare?
108C Auto/SE

108C Auto
1. Increased chamber diameter
Chamber size has been increased to permit coating of larger samples. Standard Chamber 150mm dia. x 165mm
150mm dia. 120mm dia.
2. Variable chamber geometry (option)
Adjustable chamber height is used to improve coating uniformity and vary the deposition rate
X -
3. Sample stage movements (option) Separate rotary, planetary and tilting sample movements to optimize coating distribution and coverage. X -

The 108C Auto Carbon Coater offers the choice of either manual or automatic operation.

In automatic mode, the evaporation source operates as a programmed voltage for a programmed time. The programmer is simply adjusted and displays voltage and time digitally.

In manual mode, the unique 108C Auto Carbon Coater supply can be operated in "pulse" or "continuous" with the output voltage set using the rotary control.

The 108C Auto Carbon Coater can be fitted with an optional MTM-10 Thickness Monitor. Resolution is better than 0.1nm for carbon. Careful use of the monitor and evaporation controller gives better than 5% reproducibility of coating thickness in the useful 15nm to 25nm range.

108C Auto Carbon Coater shown with the MTM-10 High Resolution Thickness Monitor (optional) Chamber shown with hinged top in the up-position Head with "Bradley type" carbon rod assembly

108C Auto Carbon Coater Accessories & Consumables
Accessories Vacuum Systems Carbon & Carbon Shaper Single & Dual Connetion Kits MTM-10 Thickess Monitor

Specifications for the 108C Auto Carbon Coater

Chamber size 120 OD x 120mm high (4.75 x 4.75")
Evaporation source Bradley type (6.15mm rods, [1/4"])
Heavy duty stainless steel construction
Evaporation supply Microprocessor based feedback loop controlled with remote current/voltage sensing; Safety interlocked by vacuum level Variable,180A max, with over-current protection
Sample table Holds 12 SEM mounts
Height adjustable through 60mm
Analog metering Vacuum Atm - 0.01mb
Current: 0 - 200A
Thickness monitoring MTM-10 High Resolution Thickness Monitor (optional)
Control method Automatic evaporation control, using programmed voltage and timer; full manual override with pulsed or continuous operation
Digital timer (0 - 9.9 seconds)
Digital volt setting (0.1 to 5.5V)
Electrical 100-120 or 200-240 VAC, 50/60Hz (specify on order)
Power 1000VA (coater and pumping system #7010 together)

Footprint (Height: 280mm)


Dimensions (mm)
1. Control unit / 2. Vacuum chamber / 3. Thickness monitor / 4. Rotary pump / 5. Anti-vibration base



Order Information

Product no. Description
9602 108C Auto Carbon Coater, 115V
9602-220 108C Auto Carbon Coater, 220V

*The 108C Auto Carbon Coater includes: Specimen Table for 12 pin-mounts; operation manual